我們將雙組份打膠機正常啟動后觀察設備的控制面板（液晶屏）。
　　We observe the control panel (Ye Jingping) of the equipment after the double component glue machine is normally started.
　　在控制面板上打開“時間設置”:“行走開始延時”設定值一般為1.00左右根據須要可調整，此參數設定值不宜太底，以免影響工作。“出膠延時”設定值一般為0.70左右,此參數設定值不能大于“行走開始延時”的參數。
　　On the control panel, open the "time settings": the "start time delay" setting value is generally around 1, according to the need to be adjusted, this parameter setting value should not be too low, so as not to affect the work. The set value of "time delay" is about 0.70, and the parameters of this parameter can not be more than "start time delay".
　　“行走開始延時”與“出膠延時”是控制打膠開的膠量的，當之間的差值越大時，打膠開始的膠量越多反之膠量少，需根據實際須要做適當的調整。
　　The "start time delay" and "glue delay" are the glue that controls the glue opening. When the difference between them is bigger, the amount of glue that starts with glue is more, and the amount of glue is less.
　　“行走停止延時”設定值一般為0.00左右。“關膠延時”設定值一般為0.05。

　　The set value of "walking stop delay" is usually about 0. The set value of "turn off delay" is generally 0.05.
　　“膠嘴刮膠時間”設定值一般為0.45左右，此參數是控制一個打膠
　　"Rubber mouth frictioning time setting value is generally about 0.45, this parameter is controlled by a glue
　　6
　　Six
　　行程即將完成時刮膠板刮膠行走的時間，如果刮膠過程中刮膠板先脫離玻璃而后提起，表示該設定值太長，須要調小;如果刮膠過程中刮膠板還沒有刮過膠嘴就提起，而且升起時與玻璃的頂力很大，表示該設定值太小，有時可能損壞玻璃，須調大。
　　The trip is nearing completion of scraping plate scraping walk time, if in the process of scraping scraping plate from the first glass and then filed, said the setting value is too long, need to adjust; if in the process of scraping scraping plate has no scratch glue mouth lifted, and the top force rises and the glass is very large, the set value is too small, sometimes may damage the glass, to increase the.
　　“停車延時”設定值一般為0.15左右。
　　The set value of "parking delay" is generally about 0.15.
　　在控制面板上打開“速度設置”:“行走速度”初使設定值為10000，根據打膠時需要膠量的多少設定，打膠量不足時，將速度值減小，反之將速度值加大。其余參數均為初使值。
　　On the control panel, "speed setting" is opened. The initial value of "walking speed" is 10000. According to the amount of glue needed to glue, the speed will be reduced when the amount of glue is not enough, otherwise the speed will be increased. The remaining parameters are all initial values.
　　您的需求就是我們努力的方向，您的追求就是我們的追求，歡迎您的到來，我們一起進步，一起創(chuàng )新！
　　Your demand is the direction of our efforts, your pursuit is our pursuit, welcome your arrival, we progress together, together innovation!